DAP Weldwood Multi-Purpose Ceramic Tile Adhesive Gallon 25192

DAP Weldwood Multi-Purpose Ceramic Tile Adhesive Quart Tub

DAP Weldwood Multi-Purpose Ceramic Tile Adhesive

Name: DAP Weldwood Multi-Purpose Ceramic Tile Adhesive
Brand: DAP
SKU: 25192-1
Price: 37.79 USD
Availability: InStock

DAP Weldwood Multi-Purpose Ceramic Tile Adhesive Gallon 25192

SKU: 25192-1

Each

$37.79 ea

Save by the box

$141.85 Box of 4 $35.46 ea

DAP Weldwood Multi-Purpose Ceramic Tile Adhesive Quart 25190

SKU: 25190-1

Each

$11.87 ea

Save by the box

$66.85 Box of 6 $11.14 ea

Selected itemsItems: 0

Total: $0.00

Product variants

Suggested Uses:

Multi-Purpose adhesive for installing most types of ceramic tile on walls, floors, and countertops.

Performance Characteristics:

Meets ANSI A136.1 Type I Requirements

Installation Tips:

Maintain adhesive, tile, and room at a stable temperature of at least 70oF (21oC) for 24 hours before and after

installation and provide adequate ventilation for at least 72 hours or until adhesive odors cannot be detected.

Surface Preparation & Application:

Surface:

Surface must be porous. Surface must be structurally sound, clean and free of dust, dirt, paint, soap

film, oil, adhesive, grease, chemical concrete-curing compounds, and other foreign material that could inhibit

bond.

Walls:

Patch large holes, replace loose plaster and smooth or level surfaces with a fast-setting underlayment

and allow to completely cure and dry out. With flat side of trowel, prime with a skim coat of DAP®

WELDWOOD® Multi-Purpose Ceramic Tile Adhesive. Allow to dry 2 to 4 hours or until notched trowel

application does not break skim coat seal. Above tub and shower receptors, cut away wall materials 1/4” above

edges and fill void with adhesive. Seal all cut edges of wall material and pack all openings with generous

amount of adhesive. Allow to dry 2 to 4 hours.

Floors:

Exterior grade plywood must be securely fastened and free of flexibility. Concrete floors must be level

to a tolerance of 1/8” in 10’, fully cured (at least 28 days), free of moisture, alkalinity, hydrostatic pressure and

not subject to dampness or seepage.

NOTE: It is the responsibility of the user to determine the dryness of all subfloors prior to installation, a

moisture test may be necessary. Follow cementitious underlayment manufacturer’s instructions for installation.

Application:

Plan tile layout, then spread adhesive with trowel held at a 45-degree angle to the surface. Apply

no more adhesive than can be covered in 25 to 35 minutes. Due to superior wet adhesive qualities, wall tiles can

be set from the top of the substrate to the bottom. Press, do not slide, tiles or sheets of tile into wet adhesive.

Maintain accurate joint alignment and spacing of tiles as they are positioned into adhesive.

To level and ensure solid tile positioning, use a wood or rubber-faced beating block tapped lightly with a rubber

mallet. Check occasionally to ensure average adhesive/title contact is not less than 80% except on shower walls

and tub installations where contact area must be 95%. To ensure 100% coverage, apply a thin layer of adhesive

on the back of each tile before firmly pressing it into wet adhesive. This method, “back-buttering” is

recommended for pavers, quarry tile, 6”x 6”, and 8” x 8” tiles. Avoid adhesive squeeze-up between tiles.

Note to Contractor:

All installation shall use procedures set forth in ANSI A-108.4 and the current TCA

Handbook for Ceramic Tile Installation. Those procedures supersede this label where applicable.

Open Time:

Approximately 25 to 35 minutes after application to substrate. Open time may vary depending on

trowel size and climatic conditions.

Cure Time:

Walls and countertops may be grouted with an appropriate grout after adhesive has set for 24

hours. For floors, allow adhesive to set for 24 to 72 hours depending on temperature, humidity and porosity of

substrate and tile. Use an appropriate grout to complete floor tile installation. Do not allow traffic over tiles

prior to grouting.

RECOMMENDED TROWEL SIZES:

Glazed Wall Tile:

3/16” x 5/32” V-notched

Ceramics, Mosaics and Gauged Slate

1/8” x 1/8” V-notched

Heavy Tile and Slate Pavers:

1/4” x 1/4“ x 3/8” Square-notched

Quarry Tile:

1/4” x 1/4“ x 1/4“ Square-notched

THIS PRODUCT IS NOT RECOMMENDED FOR MEXICAN TILES AND GREEN MARBLE.

Open Time:

25 to 35 minutes (depending upon temperature and humidity)

Cleanup:

Soapy water while wet; mineral spirits when dry

Shelf Life:

1 year when stored in original tightly sealed container

Read Reviews