Wolman DeckStrip ASR 14706

Description

Easily strip hard-to-remove acrylic stain from exterior wood with Rust-Oleum Wolman™ DeckStrip®-ASR Acrylic Stain Remover. This 100% biodegradable formula quickly removes solid or semi-solid deck and siding stains. Just spray on and power-wash off. 

• Professional strength formula - wetting agent, thickener and highest allowable concentration of active ingredient provides maximum stripping power.
• Easy to use – spray on, rinse off; no scraping or sanding.

FOR BEST RESULTS

Newer coatings, stubborn spots or multiple layers may need a second application.

One gallon covers approximately 150 sq ft depending on condition of wood and application method.

Technical Data Sheet

Extended Information

FOR EXTERIOR USE ONLY

Use DeckStrip ASR to strip and restore outdoor wood

decks, fences, siding, shakes and shingles, boat docks &

boardwalks, outdoor furniture & décor, gazebos & arbors, play sets

and more.

WOOD TYPES:

Use on all wood types, including pressure treated

lumber, Cedar, Redwood, exotic hardwoods (Mahogany,

Ipé, Teak, etc.), and North American hardwoods.

Note:

To strip traditional oil or solvent based deck stains, semi-transparent,
toners, tinted wood protectors or sealers, etc. select

Wolman DeckStrip Stain & Finish Remover and use according to
label directions.

Before You Start:

Make sure entire wood surface is dry and free of dust, dirt and debris.
If the surface is hot to the touch or in direct sunlight, dampen with fresh water to cool.

Apply when outside temperatures are above 40°F.

Pre-rinse grass, plants and shrubs surrounding the wood structure to be stripped, then

cover foliage to protect it from exposure to the product. Mask off

siding and cover all wood surfaces not intended to be stripped.

Cover any exposed aluminum surfaces (siding and flashing) to prevent

corrosion. Protect adjacent concrete surfaces from rinse

water. Sweep away surface dirt and debris. Remove any

standing water before beginning application.

Weather Conditions:

For best results, apply when outside temperature is above 50°F

(10°C), and when 24 hours of precipitation-free weather is

expected. Surface to be stripped should be out of direct sunlight

to avoid premature evaporation of the product.

A synthetic bristle brush or mop, pump sprayer or airless sprayer

(with no aluminum parts)is recommended. When working on

vertical surfaces start at the bottom and work to the top of the

structure.

Safe Handling directions must be followed to avoid exposure to

over-spray. (See Handling and Storage section)

CAUTION:

Bare wood and/or coated surfaces can become slippery when wet.

Use caution when walking on wet surfaces.

Prepare to Use:

Moderately shake container, then pour into sprayer tank. If using

a brush or mop, pour product into a 2-1/2 gallon plastic bucket.

Do not mix with any other products.

Apply:

Working on 20 sq. ft. at a time to maintain optimum surface

wetness, apply product and let sit for 15 minutes. If stripper dries

prematurely, keep it wet with additional product as needed.

Rinse

Pressure Wash:  Using a 40° tip and 1,500-2,500 PSI for pressure

-treated wood and hardwood, 500-1,000 PSI for Cedar and

Redwood, pressure-wash the surface to rinse away

dissolved coating. Move lengthwise with boards to

avoid cut marks across grain.  Repeat steps

until entire surface has been stripped. When

finished, rinse surrounding grass and plants thoroughly.

Rinse Brush and Hose: If pressure washing cannot be employed,

vigorously scrub surface with a Wolman WOODWORX® Deck Brush

or other stiff, synthetic, short-bristle broom or brush for several minutes

using moderate pressure. After brushing, rinse thoroughly with a

garden hose,using the highest pressure nozzle setting available.

On a vertical surface, continually rinse stripped areas to avoid

streaking. Rinse any wood fibers off surrounding surfaces

immediately. When dry, surface should appear clean, bright and

free of previous coating. Repeat steps until entire surface has been stripped. When

finished, rinse surrounding grass and plants thoroughly.

Note:

After stripping Cedar, Redwood or exotic hardwoods,

black tannin stains may rise to the surface and give wood an

overall darkened appearance. If this occurs, treat affected areas

with Wolman Deck & Fence Brightener liquid concentrate

to restore the natural wood color. DeckStrip ASR

is not designed to remove tannin bleed stains.

Clean Up:

Clean tools and equipment immediately after use with soap and

water. Use water or vinegar-soaked rag to wipe off any drips or

spills on unintended surfaces immediately.

Safe Handling:

During preparation and application, wear rubber or plastic

coated gloves and safety goggles. If applying with a sprayer,

wear a NIOSH-approved full-face respirator with an organic

vapor cartridge and N-95 pre-filter. Care should be taken to

cover any exposed aluminum surfaces to prevent discoloration, as this

product is corrosive to metal.

DO NOT MIX WITH ANY OTHER PRODUCTS, especially

those containing chlorine or bleach (sodium hypochlorite). Rinse

grass and plants with water after exposure.

Precautions:

DANGER! MAY BE FATAL IF SWALLOWED. CAUSES

SEVERE BURNS. CONTAINS SODIUM HYDROXIDE.

May be harmful if swallowed. Causes eye and skin irritation.

Prevent contact with eyes and skin. During preparation and

application,wear rubber or PVC gloves and safety goggles.

Wash thoroughly after handling. May cause respiratory and

throat irritation. Do not breathe spray mist. If applying with a

sprayer, wear a properly fitted, NIOSH approved respirator.

Use only with adequate ventilation.

KEEP OUT OF REACH OF CHILDREN.