SEALING
Clear B-I-N Sealer seals unpainted or porous surfaces
to improve the coverage of the topcoat.
It fills and binds wood fibers to create a smooth, sealed
surface with “enamel holdout” so fewer coats of paint are needed.
STAIN BLOCKING
Clear B-I-N Sealer will effectively blocks stains from water,
nicotine, grease, oil, soot, rust, mildew, tannin, crayon and
lipstick. It also provides an excellent odor barrier to block
odors from fire damage, smoke, cigar & cigarettes and pet
urine. Some stains may require a second coat.
ODOR BLOCKING
Clear B-I-N Sealer seals in smoke stains and odors
caused by fires. It also seals in urine and other animal
odors. It is also recommended for sealing nicotine stains
or odors from tobacco.
TINTING
Clear B-I-N Sealercan be tinted with up to 2 oz.
(60 ml) of an alcohol-based stain or aniline dye or small amount of
universal colorant per gallon. Shake container well before
using.
COVERAGE
400-600 sq.ft./gal. (9.8-14.8m2/l)
depending on application method and surface porosity.
SURFACE PREPARATION
Surfaces should be clean, dry, sound and free of dust, dirt,
excessive chalky material, grime, grease, oil, wax, mildew,
wallpaper adhesive, or any contamination that may
interfere with adhesion. If unsure of cleanliness, always
wash surface with household ammonia and water solution,
appropriate cleaning solution or solvent (Do not use TSP
as a cleaner). Remove any peeling and/or unsound
coatings. Sand any remaining paint film edges smooth
with the surface.Bare wood that has been exposed for
more than 4 weeks should be lightly sanded with 80 to 100
grit sandpaper to remove weathered wood fibers.
Countersink exposed nail heads, spot prime and fill all nail
holes and gouges with Ready-Patch® spackling compound.
Remove interior mold and mildew stains by washing the
surface with a solution of one cup household bleach
in a gallon of water. Follow label instructions and personal
protection recommendations on the MSDS. Do not add
ammonia or other cleaning products to the bleach solution.
If concerned about mold and mildew behind walls,
underneath flooring, in ventilation systems or other unseen
areas, contact a professional who specializes in mold and
mildew remediation. For commercial buildings and
schools, follow appropriate guidelines for mold removal.
WARNING!
If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved resp
irator to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
LIMITATIONS
B-I-N Advanced is not recommended for full service use
on exterior applications, for excessively humid interior
areas or surfaces subject for immersion or prolonged
contact with water. Do not box or intermix
Clear B-I-NSealer with other oil-base or water-base products.
APPLICATION
Apply only when air, material, and surface temperatures
are between 0to90ºF (-18to-32ºC) and the relative humidity
is less than 85%. Thoroughly mix or shake to
ensure any settled pigment is re-dispersed before
using. Eliminate all sources of ignition.
Do not thin this product. In most cases only one
coat is necessary to prime most surfaces. If excessive absorption
occurs over very porous substrates a second coat may be necessary.
For best results, prime entire surface before painting.
Apply with a high quality natural or synthetic brush,
3/8” nap roller, pad, conventional or airless sprayer.
If spraying, use explosion-proof equipment, and wear a NIOSH
approved respirator. Follow manufacturer's instructions when using
spray equipment.
Conventional spraying–Spray at 45-55psi.
Airless spraying-Use a 0.011-0.013" tip at 800-1000 psi.
Provide adequate ventilationat all times.
DRY & RECOAT TIMES
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures.
Dries to the touch in 15 minutes and can be recoated in 45minutes.
It is fully cured in 1-3 days.Lower temperatures,
higher humidity and the addition of tint will prolong dry and
cure time.
CLEAN-UP
Clean up spills and drips with denatured alcohol or
ammoniated detergent. If spills or drips have dried, use
denatured alcohol or ammoniated detergent to soften and
remove sealer. Wash application tools in a solution of 1
part ammonia and 2 parts water immediately after use. If
the product has dried on application tools, soak overnight
in a solution of equal parts ammonia and water. Scrub
clean with a stiff brush. Follow the equipment
manufacturer’s directions to clean spray equipment.
