Good Quality & fair price
Hi John, we're glad to hear you’re satisfied with the quality and price of our roller frames! Thanks for your support.
Krud Kutter Concrete Clean & Etch
|
Krud Kutter Concrete Clean & Etch Gallon SKU: CE01-1 |
Each
Regular price
$24.02 ea
Out of Stock
|
Save by the box
Regular price
$135.09 Box of 6
Out of Stock
|
Cleans & Prepares Concrete, Masonry & Brick for Coating, Staining or Sealing. Ideal for cleaning, degreasing, and acid etching concrete floors, walls, basements, driveways, swimming pools, patios, and containment areas prior to coating, staining or sealing.
Safer and easier to use that muriatic acid, it creates a porous surface, and provides the even profile and uniform appearance preferred for clear coating applications. Also removes efflorescence (alkali salts) and neutralizes new concrete and new mortar joints.
- Earth Friendly
- Water-Based
- Biodegradable
- Ordorless
- Non-Flammable
- Environmentally Responsible
Directions for use:
1. Mix 1/3 gallon (43 oz.) of concentrate with 1 gallon of water in a plastic sprinkling can. One gallon of concentrate will produce 4 gallons of premix; sufficient to cover 800 square feet. Hot water will accelerate cleaning and etching.
2. Sweep the surface to remove loose debris, and scrape off excess grease and oil.
3. Cleaning a 10’ x 10’ section at a time, dampen the surface with a fine spray of water, and using the sprinkling can, apply the premix evenly over the surface.
4. Scrub the premix into the surface with a stiff bristled broom until the foaming stops. NOTE: If no foaming occurs, surface has been previously sealed and this will prevent penetration of premix. Remove the sealer and reapply KRUD KUTTER CONCRETE CLEAN & ETCH premix.
5. Triple rinse the surface with a water hose. Scrub while rinsing to ensure removal of all loosened material.
6. Allow the surface to dry thoroughly before applying stain or sealant.
7. After the surface has dried, check any glossy or oily areas by applying a few drops of water. If water does not penetrate quickly, re-etch the affected areas.
COVERAGE: 200sq.ft./quart; 800sq.ft./gallon
1. Mix 1/3 gallon (43 oz.) of concentrate with 1 gallon of water in a plastic sprinkling can. One gallon of concentrate will produce 4 gallons of premix; sufficient to cover 800 square feet. Hot water will accelerate cleaning and etching.
2. Sweep the surface to remove loose debris, and scrape off excess grease and oil.
3. Cleaning a 10’ x 10’ section at a time, dampen the surface with a fine spray of water, and using the sprinkling can, apply the premix evenly over the surface.
4. Scrub the premix into the surface with a stiff bristled broom until the foaming stops. NOTE: If no foaming occurs, surface has been previously sealed and this will prevent penetration of premix. Remove the sealer and reapply KRUD KUTTER CONCRETE CLEAN & ETCH premix.
5. Triple rinse the surface with a water hose. Scrub while rinsing to ensure removal of all loosened material.
6. Allow the surface to dry thoroughly before applying stain or sealant.
7. After the surface has dried, check any glossy or oily areas by applying a few drops of water. If water does not penetrate quickly, re-etch the affected areas.
COVERAGE: 200sq.ft./quart; 800sq.ft./gallon
CAUTION
Eye and skin irritant. In case of contact with eyes or skin, flush with water for 15 minutes. If irritation persists, seek medical attention. If swallowed, take large amounts of water. Do not induce vomiting. Get medical attention.
DO NOT MIX THIS PRODUCT WITH ANY OTHER CHEMICALS.
KEEP OUT OF REACH OF CHILDREN.
CONTAINS: Phosphoric acid in a water-based solution.
NO MURIATIC ACID!
Eye and skin irritant. In case of contact with eyes or skin, flush with water for 15 minutes. If irritation persists, seek medical attention. If swallowed, take large amounts of water. Do not induce vomiting. Get medical attention.
DO NOT MIX THIS PRODUCT WITH ANY OTHER CHEMICALS.
KEEP OUT OF REACH OF CHILDREN.
CONTAINS: Phosphoric acid in a water-based solution.
NO MURIATIC ACID!