I love the brush it’s an old school brush that’s always out of stock I can’t believe you guys had it! No brush marks holds a lot of paint!
UGL Drylok Etch 01908
|
UGL Drylok Etch 10 Oz. SKU: 01908-E |
Each
Regular price
$7.87 ea
|
Save by the box
Regular price
$44.28 Box of 6
$7.38 ea
|
A modern formulation for etching masonry, stone, tile and brick. Removes efflorescence and excess mortar. For etching concrete and galvanized surfaces prior to painting.
Use DRYLOK® Etch, as a safer alternative to muriatic acid and is not activated until mixed with water for safe storage. It is perfect for treating smooth concrete and condition galvanized surfaces prior to painting.
Clean up: Water
Coverage: 300 square feet per 12-ounce container when used as a cleaner. 150 square feet per 12-ounce container when used as an etch.
- Ideal for removing efflorescence and excess mortar build-up on tile, galvanized metal, stone, concrete and brick
- Application with a stiff brush
- Fast and effective, and safer than muriatic acid
Clean and etch interior and exterior concrete, stone, tile galvanized metal and brick. Do not use galvanized container. Kills plants and shrubbery.
COMPOSITION: Sulfamic acid
SHEEN: N/A
% WEIGHT SOLIDS: 100%
% VOLUME SOLIDS: 100%
DENSITY (LBS./US GAL.): 17.74 ± 0.3
VISCOSITY: N/A
pH: 1.18 (1% solution/water)
COLORS: N/A
ACTIVE TIME: N/A
CLEAN UP: Water Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.
COVERAGE (SQ. FT./US GAL.): 300 sq. ft./12 oz. when mixed with 1 gallon of water.
Note: Actual coverage will vary depending upon application method, surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT: N/A
FLASH POINT: N/A
SHELF LIFE: N/A
FREEZE/THAW: N/A
Wear eye protection and chemical resistant gloves. Remove dirt, dust, grease and oil by washing with a detergent solution or UGL DRYLOK Concrete Cleaner & Degreaser . Allow the surface to dry before applying DRYLOK Etch.
If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH- approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
To remove efflorescence, clean mortar or etch galvanized surfaces, dissolve 12 ounces of Etch in one gallon of warm water; to etch concrete prior to painting, use 12 ounces of Etch to one-half gallon of warm water. Do not use galvanized container. Wear rubber gloves and eye protection.
Apply with a stiff brush. Wait 20-30 minutes. Flush thoroughly with clean water.
Treat smooth concrete with DRYLOK Etch. A properly etched surface should look and feel slightly rough, like fine sandpaper. If surface remains smooth, repeat the etching procedure until the surface has the proper texture. Thoroughly rinse the surface with clean water.
NOTE: Allow etching solution to remain on the surface for at least 20 minutes. While etching, the concrete surface should bubble. If some areas do not, this indicates deep oil or grease stains requiring additional cleaning. Scrub these areas again with a heavy duty detergent or UGL DRYLOK Concrete Cleaner & Degreaser and repeat the etching procedure. Allow the surface to dry at least 24 hours before staining or painting.
TOXIC–IRRITANT. Contains sulfamic acid. May cause burns. Irritates nose, throat and skin. Avoid contact with skin, eyes and clothing. In case of contact, flush with water for at least 15 minutes; for eyes, immediately flush eyes with plenty of water for at least 15 minutes. Call a physician. If inhaled, remove to fresh air. If difficulty in breathing persists, call a physician. If swallowed, give 1 or 2 glasses of water. Call physician immediately. These precautions apply to both dry form and solution.
Kills plants and shrubbery.
KEEP OUT OF REACH OF CHILDREN.
COMPOSITION: Sulfamic acid
SHEEN: N/A
% WEIGHT SOLIDS: 100%
% VOLUME SOLIDS: 100%
DENSITY (LBS./US GAL.): 17.74 ± 0.3
VISCOSITY: N/A
pH: 1.18 (1% solution/water)
COLORS: N/A
ACTIVE TIME: N/A
CLEAN UP: Water Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.
COVERAGE (SQ. FT./US GAL.): 300 sq. ft./12 oz. when mixed with 1 gallon of water.
Note: Actual coverage will vary depending upon application method, surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT: N/A
FLASH POINT: N/A
SHELF LIFE: N/A
FREEZE/THAW: N/A
Wear eye protection and chemical resistant gloves. Remove dirt, dust, grease and oil by washing with a detergent solution or UGL DRYLOK Concrete Cleaner & Degreaser . Allow the surface to dry before applying DRYLOK Etch.
If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH- approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
To remove efflorescence, clean mortar or etch galvanized surfaces, dissolve 12 ounces of Etch in one gallon of warm water; to etch concrete prior to painting, use 12 ounces of Etch to one-half gallon of warm water. Do not use galvanized container. Wear rubber gloves and eye protection.
Apply with a stiff brush. Wait 20-30 minutes. Flush thoroughly with clean water.
Treat smooth concrete with DRYLOK Etch. A properly etched surface should look and feel slightly rough, like fine sandpaper. If surface remains smooth, repeat the etching procedure until the surface has the proper texture. Thoroughly rinse the surface with clean water.
NOTE: Allow etching solution to remain on the surface for at least 20 minutes. While etching, the concrete surface should bubble. If some areas do not, this indicates deep oil or grease stains requiring additional cleaning. Scrub these areas again with a heavy duty detergent or UGL DRYLOK Concrete Cleaner & Degreaser and repeat the etching procedure. Allow the surface to dry at least 24 hours before staining or painting.
TOXIC–IRRITANT. Contains sulfamic acid. May cause burns. Irritates nose, throat and skin. Avoid contact with skin, eyes and clothing. In case of contact, flush with water for at least 15 minutes; for eyes, immediately flush eyes with plenty of water for at least 15 minutes. Call a physician. If inhaled, remove to fresh air. If difficulty in breathing persists, call a physician. If swallowed, give 1 or 2 glasses of water. Call physician immediately. These precautions apply to both dry form and solution.
Kills plants and shrubbery.
KEEP OUT OF REACH OF CHILDREN.