UGL Drylok Extreme Latex Masonry Waterproofer 28613

The next generation in waterproof coatings. This smooth waterproof paint is perfect for the most demanding conditions. Fully transferable 15-year warranty. Ideal for interior, exterior, above or below grade masonry walls, basement walls, retaining walls, foundations, landscape walls, cinder blocks, concrete blocks, bare concrete swimming pools, stucco and brick. Ceramic fortified for the ultimate in waterproof protection. Specially formulated to resist mildew growth on the paint film. Stops 12 psi, that’s greater than a wall of water 26 feet high! Passes ASTM D-7088 Resistance to Hydrostatic Pressure an ASTM D-6904 Resistance to Wind Driven Rain.

Coats: Minimum 2 coats

Clean up: Soap and Water

Coverage: 75 – 100 square feet per gallon

Dry Time: 45 minutes to touch, 2 – 3 hours to dry, 2 hours to recoat

Warranty: Fully transferable 15 Year Warranty

• Bright white flat, smooth
• Latex base
• Semi-Impermeable coating - keeps water and vapor out (<1 perm rating)
• Can be top coated after 24 hours
• Tintable
• Application by brush, roller, or sprayer

UGL Drylok Extreme Product Data Sheet

Preparation

DRYLOK® Extreme Concrete & Masonry Waterproofer may be applied on a slightly damp surface, but best results are obtained when the surface is dry, clean and free of grease, oil, form-release compound, and paint. Remove dust, dirt, and any loose or broken mortar with a wire brush. Old paint in poor condition should be removed by wire-brushing, sandblasting or other suitable methods.* If you see white, powdery, crystal-like deposits on the surface, they are naturally-occurring, water-soluble salt compounds in the masonry, pushed out by water intrusion. When the water evaporates, the salt residue remains. This effect is called efflorescence and, because it prevents DRYLOK® Extreme Masonry Waterproofer from properly bonding to the surface, it must be removed. Treat it with DRYLOK® Etch** (liquid or powder formula) or muriatic acid according to the manufacturer’s directions, rinse, and allow the surface to dry. Since efflorescence occurs naturally, we cannot warrant against it reoccurring.
Patch all cracks and holes with DRYLOK® Fast Plug®. Wet the surface to be patched. Next, back chisel the areas to be patched in the shape of an inverted ​“V” so DRYLOK® Fast Plug® can better anchor into the wall. Apply and smooth the patch so it’s even with the surface around it. As DRYLOK® Fast Plug® sets rapidly, mix only what you’ll use in 3 – 5 minutes. Also, be sure to seal the area where the floor and wall meet. Often, when concrete floors cure, they shrink and pull away from the wall, creating a space where water can enter.

Application

Schedule your project when both air and surface temperatures are 50°F or higher and, for best results, wait for a dry (rain-free) period. Stir DRYLOK® Extreme Masonry Waterproofer thoroughly before and during application — do not thin. Apply the first coat to bare masonry with a three-quarter-inch nap roller, a DRYLOK® Brush or a quality nylon bristle brush. If using a brush, work the DRYLOK® Extreme Masonry Waterproofer into the pores of the masonry, making sure to fill all pores and pinholes. If using a roller, back brush the first coat to fill all pores and pinholes. Give the first coat two to three hours to dry, and then apply a second coat using a roller, brush, or sprayer.
Proper coverage, a minimum of 2 coats, is required to warranty waterproofing. After the second coat, carefully inspect the entire surface for pinholes. Give these areas an additional coat. If leaking is still present after 2 coats, it indicates that pores or pinholes are still open. Paint these areas again.

Disposal
Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

LIMITED WARRANTY
United Gilsonite Laboratories (UGL®) warrants DRYLOK® Extreme Masonry Waterproofer, when applied according to directions on a properly prepared bare masonry surface, will provide a waterproof coating for fifteen (15) years from the date of application, warranty includes subsequent owners. There are no other warranties that extend beyond this warranty. This warranty shall not apply when the waterproofer fails due to improper product application, failure to follow label directions, inadequate surface preparation, cracked structural surfaces, reoccurring efflorescence or any conditions not foreseen by UGL. Two coats of DRYLOK® Extreme Waterproofer are required to ensure warranted waterproofing. Label directions are as complete as possible, but cannot encompass all conditions, applications and/​or surfaces. In the event that the coating fails, your remedy is limited to either replacement of the product purchased or refund of the purchase price. This is the exclusive remedy. For warranty fulfillment, return used product container and sales receipt to UGL, Technical Customer Service, 1396 Jefferson Ave., Dunmore, PA, 18509. THIS LIMITED WARRANTY EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE. UGL will in no event be liable for any incidental or consequential damages. Some States do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.