UGL Latex Drylok Original Masonry Waterproofer

Latex Base DRYLOK® Original Masonry Waterproofer is a low odor, water clean-up formula for waterproofing all interior, exterior, above or below grade masonry walls, cinder and concrete blocks, stucco, brick, retaining walls, basements, concrete swimming pools and foundation. No pre-mixing or pre-wetting necessary. Guaranteed to stop water up to 10 psi and resists 98 mph hurricane winds.

Coats: Minimum 2 coats

Clean up: Soap and Water

Coverage: 75 – 100 square feet per gallon

Dry Time: 1.5 hours to touch, 2 – 3 hours to recoat

Warranty: Fully transferable 10 Year Warranty

• Flat, sandy texture
• Semi-Impermeable coating - keeps water and vapor out (<1 perm rating)
• Can be top coated after 24 hours
• Tintable
• Coating Material: Latex
• Product Type: Masonry Waterproof Sealer
• Container Size: 1 gal
• Application Method: Brush
• VOC Level: Low VOC
• UV Resistant: No
• Time Before Recoating: 3 hr
• Tintable: Yes
• Indoor or Outdoor: Indoor and Outdoor
• Full Cure Time: 24 hr

UGL Drylok Original Product Data Sheet

Preparation
DRYLOK® Original Masonry Waterproofer may be applied on a slightly damp surface, but best results are obtained when the surface is dry, clean and free of grease, oil, form release compound, and paint. Remove dust, dirt, and any loose or broken mortar with a wire brush. Old paint in poor condition should be removed by wire-brushing, sandblasting or other suitable methods*. If you see white, powdery, crystal-like deposits on the surface, they are naturally-occurring, water-soluble salt compounds in the masonry, pushed out by water intrusion. When the water evaporates, the salt residue remains. This effect is called efflorescence and, because it prevents DRYLOK® Original Masonry Waterproofer from properly bonding to the surface, it must be removed. Treat it with DRYLOK® Etch®** (liquid or powder formula) or muriatic acid according to the manufacturer’s directions, rinse and allow to dry. Since efflorescence occurs naturally, we cannot warrant against it reoccurring. If the surface is slightly damp, wet, or efflorescence troubled, apply DRYLOK® Wet Wall Bonding Primer to troubled areas according to the label instructions. If applied to a bare masonry surface, this will not void the warranty.
Patch all cracks and holes with DRYLOK® Fast Plug®. Wet the surface to be patched and, so DRYLOK® Original Masonry Waterproofer can better anchor itself into the wall, back chisel the areas to be patched into shapes like an inverted ​“V”. Apply and smooth the patch so it’s even with the surface around it. As DRYLOK® Fast Plug® sets rapidly, mix only what you’ll use in 3 to 5 minutes. Also, be sure to seal the area where the floor and wall meet. Often, when concrete floors cure, they shrink and pull away from the wall, creating a space where water can enter.

Application
Schedule your project when both air and surface temperatures are 50ºF or higher and, for best results, wait for a dry (rain-free) period.
Cancer hazard: Contains Crystalline Silica, which can cause cancer***.
Stir DRYLOK® Original Masonry Waterproofer thoroughly before and during application — do not thin. Apply the first coat to bare masonry with a three-quarter-inch nap roller, a DRYLOK® Brush or a quality nylon bristle brush. If using a brush, work the DRYLOK® Original Masonry Waterproofer into the pores of the masonry, making sure to fill all pores and pinholes. If using a roller, back brush the first coat to fill all pores and pinholes. Give the first coat three hours to dry, and then apply a second coat using a roller or brush.
Proper coverage, a minimum of 2 coats, is required to warranty waterproofing. After the second coat, carefully inspect the entire surface for pinholes. Give these areas an additional coat. If leaking is still present after two coats, it indicates that pores or pinholes are still open. Paint these areas again. When painting the inside of concrete fish ponds and non-potable water tanks, allow DRYLOK® Original Masonry Waterproofer to dry at least one week, then fill with water.

Disposal
Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

Warranty
LIMITED WARRANTY
United Gilsonite Laboratories (UGL®) warrants DRYLOK® Original Masonry Waterproofer, when applied according to directions on a properly prepared bare masonry surface, will provide a waterproof coating for ten (10) years from the date of application, warranty includes subsequent owners. There are no other warranties that extend beyond this warranty. This warranty shall not apply when the waterproofer fails due to improper product application, failure to follow label directions, inadequate surface preparation, cracked structural surfaces, reoccurring efflorescence or any conditions not foreseen by UGL. Two coats of DRYLOK® Original Masonry Waterproofer are required to ensure warranted waterproofing. Label directions are as complete as possible, but cannot encompass all conditions, applications and/​or surfaces. In the event that the coating fails, your remedy is limited to either replacement of the product purchased or refund of the purchase price. This is the exclusive remedy. For warranty fulfillment, return used product container and sales receipt to UGL, Technical Customer Service, 1396 Jefferson Ave., Dunmore, PA, 18509.
THIS LIMITED WARRANTY EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE. UGL will in no event be liable for any incidental or consequential damages. Some States do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.